A properly maintained lubrication schedule will provide a smooth running machine for many years. All pivot locations have grease fittings. The following table gives an example of a schedule for lubricating. Please note, this is is only a guideline and should not be used to replace any existing maintenance schedules.

TD65/TD65-2
Spindle Assemblies	4-8 hours
Wing Deck Pivots(3)	As Required
Rear Deck Pivots(2)	As Required
Castor Wheels/Swivels	As Required
Input PTO	Yokes: Every 8 Hours (Until grease exits bearings) Shield Bearing: Every 8 Hours (1 pump) Inside Tubes : Pull apart and lubricate once per week
Intermediate PTO	Yoke: Every 8 Hours (Until grease exits bearings) Shield Bearing: Every 8 Hours (1 pump) Inside Tubes: Pull apart and lubricate once per week
Deck PTO	Yokes: As Required (Until grease exits bearings) Shield Bearing: As Required (1 pump) Inside Tubes : Pull apart and lubricate once per week
Hanger Bearing	Every 8 Hours (Until grease exits bearing)
Frame Pivots(8)	As Required
Wheels	As Required
Gearbox Oil	**See Bottom of Page**

TD92
Spindle Assemblies	4-8 hours
Wing Deck Pivots(3)	As Required
Rear Deck Pivots(2)	As Required
Castor Wheels/Swivels	As Required
Input PTO	Yokes: Every 8 Hours (Until grease exits bearings) Shield Bearing: Every 8 Hours (1 pump) Inside Tubes : Pull apart and lubricate once per week
Intermediate PTO	Yoke: Every 8 Hours (Until grease exits bearings) Shield Bearing: Every 8 Hours (1 pump) Inside Tubes: Pull apart and lubricate once per week
Deck PTO	Yokes: As Required (Until grease exits bearings) Shield Bearing: As Required (1 pump) Inside Tubes : Pull apart and lubricate once per week
Hanger Bearing	Every 8 Hours (Until grease exits bearing)
Frame Pivots(8)	As Required
Wheels	As Required
Gearbox Oil	**See Bottom of Page**

Pro-Max 36
Spindle Assemblies	4-8 hours
Wing Deck Pivots(3)	As Required
Castor Wheels/Swivels	As Required
Input PTO	Yokes: Every 8 Hours (Until grease exits bearings) Shield Bearing: Every 8 Hours (1 pump) Inside Tubes : Pull apart and lubricate once per week
Intermediate PTO	Yoke: Every 8 Hours (Until grease exits bearings) Shield Bearing: Every 8 Hours (1 pump) Inside Tubes: Pull apart and lubricate once per week
Deck PTO	Yokes: As Required (Until grease exits bearings) Shield Bearing: As Required (1 pump) Inside Tubes : Pull apart and lubricate once per week
Hanger Bearings	Every 8 Hours (Until grease exits bearing)
Frame Pivots(8)	As Required
Wheels	As Required
Gearbox Oil	**See Bottom of Page**

Pro-Flex 120
Spindle Assemblies	Daily
Lift Arm Pivots(4 each)	As Required
Wing Pivots(2)	As Required
Castor Wheels/Swivels	As Required
Input PTO	Yokes: Every 8 Hours (Until grease exits bearings) Shield Bearing: Every 8 Hours (1 pump) Inside Tubes : Pull apart and lubricate once per week
Intermediate PTO	Yoke: Every 8 Hours (Until grease exits bearings) Shield Bearing: Every 8 Hours (1 pump) Inside Tubes: Pull apart and lubricate once per week
Hanger Bearing	Every 8 Hours (Until grease exits bearing)
Idlers(8)	As Required
Wheels	As Required
Swivel Hitch	As Required
Gearbox Oil	**See Bottom of Page**

TDR-15
Spindle Assemblies	4-8 hours
Wing Deck Pivots(3)	As Required
Rear Deck Pivots(2)	As Required
Swivels	As Required
Input PTO	Yokes: Every 8 Hours (Until grease exits bearings) Shield Bearing: Every 8 Hours (1 pump) Inside Tubes : Pull apart and lubricate once per week
Intermediate PTO	Yoke: Every 8 Hours (Until grease exits bearings) Shield Bearing: Every 8 Hours (1 pump) Inside Tubes: Pull apart and lubricate once per week
Deck PTO	Yokes: As Required (Until grease exits bearings) Shield Bearing: As Required (1 pump) Inside Tubes : Pull apart and lubricate once per week
Hanger Bearing	Every 8 Hours (Until grease exits bearing)
Frame Pivots(8)	As Required
Wheels	As Required
Gearbox Oil	**See Bottom of Page**

TDR-22
Spindle Assemblies	4-8 hours
Wing Deck Pivots(3)	As Required
Rear Deck Pivots(7)	As Required
Swivels	As Required
Input PTO	Yokes: Every 100 Hours (Until grease exits bearings) Shield Bearing: Every 100 Hours (1 pump) Inside Tubes : Pull apart and lubricate once per week
Intermediate PTO	Yoke: Every 100 Hours (Until grease exits bearings) Shield Bearing: Every 100 Hours (1 pump) Inside Tubes: Pull apart and lubricate once per week
Deck PTO	Yokes: As Required (Until grease exits bearings) Shield Bearing: As Required (1 pump) Inside Tubes : Pull apart and lubricate once per week
Frame Pivots(8)	As Required
Wheels	As Required
Gearbox Oil	**See Bottom of Page**

SDR-65
Spindle Assemblies	4-8 hours
PTO	Yokes: Every 8 Hours (Until grease exits bearings) Shield Bearing: Every 8 Hours (1 pump) Inside Tubes: Pull apart and lubricate once per week
Gearbox Oil	**See Bottom of Page**

SDR-90
Spindle Assemblies	4-8 hours
PTO	Yokes: Every 8 Hours (Until grease exits bearings) Shield Bearing: Every 8 Hours (1 pump) Inside Tubes: Pull apart and lubricate once per week
Gearbox Oil	**See Bottom of Page**

---

Gearbox Oil Levels
Deck Gearboxes:
Gearboxes all have an oil level plug located on the side of the gearbox. Oil should reach the bottom of this hole. If oil level is low, add oil through top plug hole of casing until oil just starts to flow out of the side oil level hole. Replace and tighten plugs. Use 80W90 Gear Oil or equivalent.

4-Shaft Gearboxes:
The main gearbox has a combination filler plug and dipstick. Remove the plug, dry off the dipstick and replace to check oil level. It must touch the oil in the gearbox. Add oil as required. Replace and tighten the plug. Use 80W90 gear oil or equivalent.